SPB 32-42

SPB 32-42

Rent Buy New View Inventory

Despite its simplicity, this machine guarantees high performance in terms of speed and push.

The frame is made of high quality steel, and the parts mostly subject to stresses have been ribbed and boxed to ensure maximum resistance, though keeping the machine weight as light as possible. The hydraulic system has 5 spools; the fifth spool may be used to control the hydraulic mandrel, if fitted. The separate valves enable the operator to set the mandrel pressure independently from the machine. The hydraulic cylinders are sized in such a way that they can operate with pressures exceeding 300 bar. The system design and the proportional valves offer excellent modularity and sensitivity of machine movements, at the same time making the machine speed and push very easy to control.

The new position of the piloting platform and the engine compartment on opposite sides make this machine unique in terms of operating comfort and guarantee maximum visibility and low noise levels to the operator. The SPB 32-42 is installed on tilting idle tracks. Its dimensions and low profile make its travel easy on any job site. The Caterpillar chains are equipped with three bar shoes, the rollers are life-long lubrication type, and the track tensioning device is greased type. All these elements guarantee maximum machine reliability and life over time. On request, LGP tracks are available.

 

Specifications

Engine
Engine Model

Caterpillar C-6.6 ACERT

Horsepower

168 kW / 225 HP

Net Flywheel Power (DIN 6271)

225 HP / 168 Kw

Governed Speed

1,900 rpm

Displacement

6.6 liters

Compression Ratio

16:01

Engine Bore

105 mm – 127 mm

Number of Cylinders

6

Hydraulic Winch
Max. Pull At First Layer

17,306 lbs / 7,850 kg

Hydraulic Motor

Orbital DANFOSS

Frame

Aluminum allow + ductile cast iron

Reduction Gear

With worm screw, irreversible

Neutral

Manual

Max Operating Pressure

4640 psi / 320 bar

Maximum Feed Flow Rate

26 U.S. gal/min – 100 L/min

Speed at First Layer

16 ft/min – 4,85 m/min

Recommended Cable Diameter

1/2 inch / Ø 10mm

Wire Rope Type

6 strands with textile core

Hydraulic Pump
Maximum Flow Rate

108 U.S. gal/min – 410 L/min

Maximum Constant Pressure

127 U.S. gal/min – 483 L/min

Maximum Peak Pressure

320 bar

Front Cracking Wheel
Hydraulic Motor

Orbital DANFOSS

Hydraulic Tank
Hydraulic Oil Tank Capacity

76 U.S. gal / 290 L

Hydraulic Oil Tank
Hydraulic Oil Tank Capacity

76 U.S. gal / 290 L

Control Valve
Control Valve Brand

Rexroth

Spools

N.5

Fuel Tank
Fuel Tank Type

Metal work with filter

Features

Pipebender

Cabin

Optional Cabin

Available on select models, this cabin is insulated and can be fitted with A/C or heater as part of our winterization package.

Platform

Operator’s Platform

Placed opposite the engine for maximum comfort and great visibility.

Winch

Hydraulic Winch

Pulling capacity ranging from 3,000 to 10,000 kg.

Hydraulic System

Load-sending variable pump and a five-spool proportional valve, allowing safer, faster and precise control.

Tracks

Tracks

Caterpillar-type crawler undercarriages with triple grouser bars on industrial-grade shoes.

Gallery

Accessories

Mandrels

Mandrels

Model Pipe Range Weight

Line-up Clamps

Clamp

Model Pipe Range Weight

Bending Sets

Bending Set
Each bending set will fit one pipe size only and it includes: a stiff back liner; a bending die; two pin-up clamp liners; and a pin-up liner.

Bending sets are available bare or with linings to accommodate special conditions and non-standard pipe or coating. Standard bending sets will accommodate pipe manufactured to API-5L.

The largest pipe size in a given pipe bending machine range requires a bending die only.